MLCS 9410 20-Amp Heavy Duty Router Speed Control

From the Manufacturer

Features include: Adjustable speed from 0 RPM to full speed, 3 position rocker switch-Variable, Off or Full Speed, Full power and torque at all speeds, Sturdy Aluminum Case. Go back and forth from any preset speed to full speed at the flip of a switch. Works with all routers 3-1/4 HP or less. 120V, 20AMP. Give your router a feature only available on routers costing hundreds of Dollars. Easy to use-Simply plug in speed control and plug your router into the speed control turn dial slowly for best results. (Speed control has a clip that can be worn on your belt, hung on wall, or left loose). Using a speed control decreases tear out, stops burning, lets you feed at comfortable rate, provides better, safer results with large diameter panel raising bits, decreases wear on bits, makes less noise, and allows softer starts at lower speeds. A Dust Cover is included (not shown in photo). NOTE: Will not work with soft start or variable speed routers.

(more…)

MLCS 9078 20-Amp Safety Router Table Power Switch

From the Manufacturer

This convenient, mechanical push button switch features a large paddle “stop”, to allow you to quickly shut off power to your 120-Volt ac machinery. Placing the switch where you can use your hip or knee to bump it into the “off” position gives you the freedom to never take your hands off the work-Piece to turn off the machine. Surface mounts quickly and easily. Maximum 20-Amps.

(more…)

Business Logo Design

MLCS 9167 Safety Push Block and Stick Package, 5-Piece

From the Manufacturer

The MLCS push blocks and sticks set offers a safe and convenient way to run stock on your router table, shaper, table saw or jointer. They keep your hands safely away from cutting edges. They are made with high friction rubber pads on their underside so that you get a sure grip. The notch-stick has a slender profile that is ideal for narrow pieces. Shaped to hold down as well as feed.

The MLCS Push Blocks & Sticks Set offers a safe and convenient way to run stock on your router table, shaper, table saw or jointer. They keep your hands safely away from cutting edges. They (more…)

MLCS 9326 Woodworking 24-Inch Flexible Curve Ruler

From the Manufacturer

Our flexible curve rulers are adjustable to hold shape and give precise measurements on curved edges. Raised edge lets you draw a line. Calibrated in 1/16-Inch measurements on one side and 1mm increments on the other side. Made of plastic. 24-Inch long.

(more…)

MLCS 9325 12-Inch Woodworking Flexible Curve Ruler

From the Manufacturer

Our flexible curve rulers are adjustable to hold shape and give precise measurements on curved edges. Raised edge lets you draw a line. Calibrated in 1/16-Inch measurements on one side and 1mm increments on the other side. Made of plastic. 12-Inch long.

(more…)

MLCS 9327 Woodworking 36-Inch Flexible Curve Ruler

From the Manufacturer

Our flexible curve rulers are adjustable to hold shape and give precise measurements on curved edges. Raised edge lets you draw a line. Calibrated in 1/16-Inch measurements on one side and 1mm increments on the other side. Made of plastic. 36-Inch long.

(more…)

MLCS 200 Solid Carbide Spiral Upcut Bit Starter Set, 3-Piece

From the Manufacturer

Three solid micro grain carbide bits for fast, smooth cuts and an edge that stays sharp longer. Spiral bits produce a very clean and accurate cut with minimal chatter. Upcut spiral helps remove material from the groove. They work well for deep mortises, cutting dadoes in a router table and any edge treatment done with the work facing upward. Includes the following diameter UPCUT bits: 1/4-Inch D (1-Inch cutting length, 1/4-Inch shank), 1/2-Inch D (1-1/2-Inch cutting length, 1/2-Inch shank) and 3/8-Inch D (1-1/4-Inch cutting length, 1/2-Inch shank).

Three SOLID MICROGRAIN CARBIDE bits for fast, smooth cuts and an edge that stays sharp longer. Spiral Bits produce a very clean and accurate cut with minimal chatter. Upcut spiral helps remove material from the groove. They work well for deep mortises, cutting dadoes in a router table, and any edge treatment done with the work facing upward. Includes the following diameter UPCUT B (more…)

MLCS 7733 60-Degree Woodworking Edge Banding Tongue and Groove Set, 1/2-Inch Shank, 2-Piece

From the Manufacturer

Add an attractive and durable edge to your cabinet doors and shelf edges. For use with plywood panels, MDF panels or shelves from 1/2-Inch to 1-Inch thick. All matched 2 piece bit sets are two-flute, carbide-tipped. Simply center the male cutter on the stock and make the cut. Next match up the female cutter with the center point of the first cut. Finish by gluing together the two pieces and flush trim the edges, if necessary. 60-Degree bits feature a tongue and groove for a larger glue surface area and easier alignment of edge banding. 1-7/16-Inch large diameter. 1-Inch carbide height. Recommended for use in a table mounted router.

Add an attractive and durable edge to your cabinet doors and shelf edges. For use with plywood panels, MDF panels or shelves from 1/2″ to 1″ thick. All matched 2 piece bit sets are two-flute, carbide-tipped. Simply center the male cutter on the stock and make the cut. Next match up the female cutte (more…)

MLCS 8376 Plywood Straight Router Bit 3-Piece Boxed Set

From the Manufacturer

Boxed Set includes 3 quality Carbide-tipped router bits in common metric plywood sizes: 13/64″ (5.2 mm–for 1/4″ undersize), 31/64″ (12.3 mm–for 1/2″ undersize), and 23/32″ (18.2 mm–for 3/4″ undersize). All Bits are 1/2″ shank.

Boxed Set includes 3 quality Carbide-tipped router bits in common metric plywood sizes: 13/64″ (5.2 mm–for 1/4″ undersize), 31/64″ (12.3 mm–for 1/2″ undersize), and 23/32″ (18.2 mm–for 3/4″ undersize). All Bits are 1/2″ shank.

(more…)